KNOWING PLUMBING BASICS IS CRUCIAL FOR INSTALLING A BATHTUB

Knowing Plumbing Basics is Crucial For Installing a Bathtub

Knowing Plumbing Basics is Crucial For Installing a Bathtub

Blog Article

Book

On this page in the next paragraph you can find additional helpful additional info pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


Installing A Bathtub
Setting up a bath tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably tough task. If the old tub is easily obtainable, the project can move easily; if you have to open up a wall to get rid of the old bathtub and place the new bathtub, the task is a lot harder. In either case, the job is within a house handyman's skills, although you will require a helper to leave the old bathtub as well as set in the new one. Ensure you have certified on your own for the task and also fit attempting it. Rather than hiring a specialist to take over a halfway-completed task, it is better to take into consideration using one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This write-up will certainly assist you set up a new bath tub in your restroom if you have currently bought a new tub and also do not require to alter the setup of your previous supply of water pipes.
Your devices and also material list need to consist of the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is separate the water supply. After doing so, activate the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be rather problematic due to the restricted gain access to that is commonly the situation.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will originate from the pipes. When the supply pipelines have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing substance.
    Prior to carrying on to fit the new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a link to the existent supply pipes.
    If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, position the faucet in the placing opening in the bath/basin making certain that the washers remain in place between the tap as well as the sink. Secure the tap in position with the maker offered backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former kind should be attached to the tap finishes first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Mounting the Bath tub


    Making use of the two wood boards under its feet, place the bathtub in the required setting. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
    The following objective is to ensure that the tub is leveled all round. This can be achieved by checking the level and adjusting the feet on the tub till the spirit level reads level.
    To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; after that do the same for the other faucet.
    Switch on the water system and also examine all joints and new pipework for leaks and tighten them if required. Fill up the bath tub as well as likewise inspect the overflow outlet and also the regular outlet for leakages.
    Lastly, take care of the bathroom paneling as described in the producer's instruction manual. Tiling and also securing around the tub ought to wait until the tub has been utilized at least when as this will certainly resolve it right into its final placement.

    Getting ready for the Installation


    First of all, the supporting framework provided with the bath must be fitted (if required) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to stop stress on the tub.
    Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of every one of the provided washing machines.
    Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final placement.

    Tiling Around the Bath tub


    In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to complications with moisture and also feasible leaks to the ceiling listed below.
    You can choose from a variety of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealant can fracture rather early if you do not think about this movement before sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily available on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or water resistant adhesive as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    Hopefully you enjoyed our topic about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for taking a few minutes to read our short article. Don't hesitate to take a moment to promote this blog posting if you liked it. Thanks for your time. Don't forget to pay a visit to our site back soon.


    Emergency? We're here!

    Report this page